A PlugIn is an interface between IPEmotion and any desired measuring system, control unit, or protocol. This interface supports various transport layers like Ethernet, USB, and serial communication. A Software Developer Kit (SDK) package is available for standardized PlugIn development, which can be selected in the custom or full installation.
Description
Configuration and data acquisition (TEDS, STG, IEPE, Voltage, High Voltage, mA, RTD, TC, DIO, PWM, Encoder) using IPETRONIK measurement devices via CAN bus or X-LINK and XCP on Ethernet.
X-LINK devices Mx-SENS2 4 and Mx-STG2 6 are supporting sample rate up to 100 kHz/channel.
Vendor: IPETRONIK
Description
The CAETEC dataLog PlugIn is supporting the configuration of µCROS, ETHOS and ARCOS product lines.
Vendor: IPETRONIK
Description
ECU protocol measurement and calibration based on CCP, XCPonCAN, XCPonETH. Bus traffic analysis CAN, LIN and FlexRay and CAN traffic output simulation. Diagnostics measurements using OBD, WWH-OBD, KWP, GM-LAN, UDS, J1939. Intelligent imports for CAN dbc / XML, LDF, Fibex, FlexRay, Autosar, A2L und GM-LAN description files.
Vendor: IPETRONIK
Description
The CANWAY PlugIn for IPEmotion is used to configure the CW-401 MkII current clamps and allows the setting of parameters such as CAN ID, output rate, signal name, etc.
Vendor: CANWAY Technology GmbH
Description
Developed for measurements on various units and HV components in vehicles or on test benches.
Vendor: IPETRONIK
Description
Measurement data acquisition from EtherCAT systems. IPEmotion acts as EtherCAT master and can acquire signals from connected EtherCAT slaves. Signals can be imported via an ENI description file (EtherCAT Network Information).
Vendor: IPETRONIK
Description
Access to Siemens S7 automation systems with different interfaces. Configurations can be created by importing STEP 7 .s7p and TIA .ap1 project files in order to select the variables of interest.
Vendor: IPETRONIK
Description
Access to the Profibus PLC network to operate in master or slave mode.
Vendor: IPETRONIK
Description
Configuration and data acquisition of Beckhoff TCP/IP field bus couplers with K bus terminals. Interfacing to TwinCAT PLCs based on EtherCAT EL-terminals is also supported.
Vendor: IPETRONIK
Description
Configuration and data acquisition via Ethernet TCP/IP field bus couplers for digital and analog signals.
Vendor: IPETRONIK
Description
Measurement data acquisition and communication via OPC UA (Open Platform Communications Unified Architecture). Standardized communication protocol for data exchange between OPC UA servers and clients.
Vendor: IPETRONIK
Description
Interfacing any MODBUS devices using either RTU interface (serial) or TCP interface (LAN). Supporting many function codes to set and read registers. PlugIn is licensed.
Vendor: Technikmedia
Description
With this version of Aerospace Protocol PlugIn, you have the ability to communicate with ARINC429 net.
Vendor: IPETRONIK
Description
Data acquisition boards for dynamic applications.The PlugIn support many real-time configuration functions with the exception of the on-board FFT calculation. Automatic hardware detection is implemented.
Vendor: Goldammer
Description
Interface to QuantumX MX840 universal signal conditioning device for Current, Volt, RTD, Thermocouple and Strain Gauge measurement.
Vendor: IPETRONIK
Description
K8055 evaluation board for students. Automatic hardware detection over the USB port.
Vendor: IPETRONIK
Description
Enables IPEmotion to read data from serial devices. The PlugIn provides the framework for device-specific DLL to handle data communication.
Vendor: IPETRONIK
Description
Data recording of current, voltage and power and many characteristics from power analyzers.
Vendor: IPETRONIK
Description
Serial communication to scales.
Vendor: IPETRONIK
Description
Recording GPS data based on the NMEA standard protocol.
Vendor: IPETRONIK
Description
Recording the sound signal from the PC microphone / sound card.
Vendor: IPETRONIK
Description
Recording of video data in IPEmotion from USB web cams and IP cameras with the Real Time Streaming Protocol (RTSP).
Vendor: IPETRONIK
Description
Send and receive ASCII data records via the UDP or TCP protocol. The specific AK protocol for data communication to MAHA roller test benches is also implemented.
Vendor: IPETRONIK
Description
The PlugIn summarizes various sensors that support CAN interfaces.
This includes the following devices:
Vendor: IPETRONIK